Відео

will taking printout of circuit on normal paper using Inkjet printer work ?

Dont use glue to layer the two OH-papers. just use tape like wtf.

🎉🎉🎉🎉 i think you have done LLB in Mass Communication😅😅😅😊

Lovely, thank you so much, I’m using your version to rehearse for our Carol service this year. So grateful 🙏

👍🏻👍🏻👍🏻👍🏻👍🏻👏👏👏👏👏👏

very slow...I've seen a much better technique...the wire is to thin and no heatshrink...also wouldn't solder on that table...😮

Fake he showed ordered pcb. Home made3

You know you can get a nozzle for your syringe and use a little brush right?

This guy is a hack. Everything he shows is bad tecnique.

easy when you know how to do it - thx for good video

No es cosa, mejor encargar a las grandes empresas dedicadas, te sale mucho mas barato y no hay color nunca mejor dicho

That is a lousy solder!! Do not follow this method.

thanks

What setting did you set your laminator to?

Hello, take a look at my videos and know my method to remove all unwanted copper from PCB: ua-cam.com/video/YYOK-OV0dBU/v-deo.html ua-cam.com/video/cOwtDCRsyFI/v-deo.html ua-cam.com/video/FqLnyxBqjjA/v-deo.html A big hug!

Thank you. So simple when you know how.

And of course.Don't forget to mention that this film is negative.And.It should of course go with sodium carbonate.You can use sodium hydroxide.But mixed it with water.To lower the pH.Ethanol works too.

Hello , Great job and a descriptive video Thanks a lot . My questions , From where did u procure the photosensitive film ? also the chemicals required . Any online dealers in India ? I am based in Delhi NCR . Thanks

Pls what is the name of the app you use to make your PCB design

Is it best to use acetone or 70% alcohol to clean the PCB before applying the film? Is Sodium Hydroxide better to use than Sodium Carbonate for the developer? I tried with NaCO3 for 2 mins and did not get great results. I need to rub the board gently with my finger afterwards.

Do you have to remove the plastic layer before putting it into the Sodium Carbonate solution?

Good information..

even though there isn't a voice over the music isn't bad its nice and soft. spread the paint by putting a pane of glass over it and your mask will look 10x better.

Thumbs Down! I can get past the lack of narration or sub titles but as slow and drawn out for time this is, It's best watched either at 1.5 or 2.0 speed otherwise a good video.

Couldn't have done a worse job if he tried. Laughed all the way with this moron.

Cool :)

This music rips! I love it

when add hydrocsoduim in Photosensitive Dry Film all go on nothing stay in board curict or line what the reason , it in wihte led not uv led

Will any laminator work for this? Did you have to modify it in any manner as I have seen some people do?

Thanks

Bhai kis sheet pe degsin Kiya h glass,finolic, ya HPC pe

thanks for your time and sharing with us, and better silent than with these horrible songs that have in many videos on youtube, my only question: No question, the video is a complete tutorial.

even with this process at times marker pen is needed. Dry film registration is suspect unless we pass more rounds thro the laminator. unless we resot to electric iron, extra burden buying a laminator , moding the heating temp . etc Thanks sarma vu3zmv

I heard adding some citric acid to the resist development helps what do you think?

Wonderful tutorial. Thanks for sharing.

bade zabardast Idea sirji

Is this uv curable stuff the same used for silk screen printing?

This video help you to Make your PCB like a Pro in 8 steps (LCD Module NOKIA 3310) ua-cam.com/video/vLauEnn1l_Y/v-deo.html

Excuse me sir, what is the printer, ink, and paper did you use for make the transparancy film like that?

Perfect! Thanks a lot! 😁👍🏼

Not sure why there are dislikes. this is the best video for achieving this. There just isn't sound.

Good job , Please go on

very unprofessional. all the time you touch the pcb with your fingers leaving greasy prints. after exposure, the tile must be set aside from 15 minutes to 2 days as well as after lamination until the board reaches room temperature. the plate can be soaked in distilled water at 90 C after exposure to improve the contrast between exposed and non-exposed areas. sodium carbonate solution must be 3%

Yawn

Brilliant thank you. Dry is so much easier than wetting

We can cut more easily by tin snips

0. Use a transparent film to print the negative of the design (print two of them) 1. Peel off the top layer to paste the film on the board 2. Use heat (lamination machine, around 100°C) to strengthen the adhesion 3. Place the board with the film on it, in sunlight for 4 - 7 minutes, to start the degradation process. 4. Remove the second layer of the film & use Sodium Carbonate as a developer (with ratio 1gram:1 cup (100ml) of water) to clear off the exposed area of the film. Keep it in the solution until etching is done. 5. Then place it in the Sodium Hydroxide solution to etch the copper PCB is ready!

thanks

well i fudged my first attempted because i didn't remember the steps fully. i didn't get a laminator or use any heat, my mask is covering the wrong parts and needs to be inverted and reprinted. thats what i get for no thinking about it for a month.

Thank you. I have been tearing my hair out trying to get top layer off.